Launch offer — valid today only

📄 Digital book in PDF · read it on your phone or print it

The Red Seal Millwright Exam, Fully Illustrated One Topic per Page, So You Can Picture It at the Exam

For the interprovincial millwright exam in Canada, in metric. Bearings, couplings, shaft alignment, rigging, pumps, hydraulic symbols and trade math: each topic on its own page, the drawing first, then what you need to remember. 65 illustrated pages.

I WANT THE ILLUSTRATED BOOK

🔒 Secure checkout · PDF by email · 30-day guarantee

Every topic, its own pageEach technique drawn, with the explanation right beside it
65 illustrated pages9 parts, from the exam and lockout to the final formula review
Up-to-date sourcesRed Seal Occupational Standard, CSA Z460 and provincial OHS regulations
PDF by emailFormat

Look Inside the Book

Every page has one big drawing and a box with the numbers and steps you need to know:

135 questions · 70% to pass · 4 hours · blocks A to F with their counts
135 questions · 70% to pass · 4 hours · blocks A to F with their counts
7 mm + 0.5 mm + 0.28 mm = 7.78 mm: the micrometer read step by step
7 mm + 0.5 mm + 0.28 mm = 7.78 mm: the micrometer read step by step
Induction heating to about 110 °C, max 120 °C, and force only through the fitted ring
Induction heating to about 110 °C, max 120 °C, and force only through the fitted ring
1750 rpm motor, 100 mm pulley driving 250 mm: 700 rpm, worked step by step
1750 rpm motor, 100 mm pulley driving 250 mm: 700 rpm, worked step by step
Offset and angular, vertical and horizontal: the four values every alignment corrects.
Offset and angular, vertical and horizontal: the four values every alignment corrects.
BC: 6 broken wires in one lay, hook throat +15%, web sling max 82 °C
BC: 6 broken wires in one lay, hook throat +15%, web sling max 82 °C
100 mm bore at 10 MPa ≈ 78.5 kN; retract force uses piston area minus rod area.
100 mm bore at 10 MPa ≈ 78.5 kN; retract force uses piston area minus rod area.
NPSH available > NPSH required · gravel noise, vibration, pitted vanes · throttle on discharge only
NPSH available > NPSH required · gravel noise, vibration, pitted vanes · throttle on discharge only

Swipe to see more →

These are real pages from the book. The table of contents is the full one: 9 parts and 61 topics.

The Problem Isn't You. It's How It Was Explained to You.

You're at the exam table and the question shows a shaft with a heavy radial load and some thrust. Ball, cylindrical, tapered or spherical roller? At the plant, you'd know by looking at the housing.

On paper, it won't come to you. The module covers bearing types in pages of paragraphs, load directions buried between part numbers, and nothing you can picture.

Induction heating to about 110 °C, max 120 °C, and force only through the fitted ring

In this book, that topic is one page. Ball, cylindrical, tapered and spherical roller bearings sit next to a plain bushing, each with arrows showing the load it carries: radial, thrust or both.

The same goes for bearing numbers, which ring gets the tight fit, rim-and-face readings, sling angles and directional control valves: each one has its own page.

You read the question, picture the drawing and pick the answer. No flipping back through the manual.

COMPARE FOR YOURSELF

The Same Topic, Two Ways to Study It

THIS
  • The manual: line after line
  • Micrometer readings explained only in words
  • You walk into the exam with doubts
The metric outside micrometer employs a screw thread with a pitch of 0.5 mm, such that one complete revolution of the thimble advances the spindle by 0.5 mm. The sleeve is graduated in whole millimetres above the datum line and in half millimetres below it, while the thimble carries fifty equal divisions, each representing 0.01 mm. To obtain a reading, the technician adds the last visible millimetre graduation, any exposed half-millimetre graduation and the thimble division coinciding with the datum line, taking care to avoid parallax.
FOR THIS
  • The micrometer in one drawing
  • Each step of the reading in a box
  • You see it and you get it
7 mm + 0.5 mm + 0.28 mm = 7.78 mm: the micrometer read step by step
CONTENTS

Take a Look at the 9 Parts and 61 Topics

Exam and safety, measuring and trade math, bearings, power transmission, shaft alignment, rigging, hydraulics and pneumatics, pumps and vibration, and a final review: 65 pages, all illustrated

IBefore You Start: Exam and Safety · pp. 5-9
  1. How the Red Seal Millwright Exam Is Built
  2. Lockout: Zero Energy Before You Touch It
  3. Oxy-Fuel and Hot Work
  4. Bolt Grades and Strength Marks
  5. Threads and Tap Drill Size
IIMeasuring and Trade Math · pp. 10-17
  1. Reading a Metric Micrometer
  2. Reading a Vernier Caliper
  3. Dial Indicator Basics and TIR
  4. Metric and Imperial Conversions You Still Meet
  5. Areas and Tank Volumes
  6. Working Out a Load's Weight
  7. Thermal Expansion
  8. Fits: Clearance, Transition, Interference
IIIBearings · pp. 18-24
  1. Plain or Rolling: Which Bearing Carries What
  2. Reading a Bearing Number
  3. Which Ring Gets the Tight Fit
  4. Mounting a Bearing Without Damaging It
  5. Adapter Sleeves and Clearance Reduction
  6. Bearing Lubrication: How Much Grease
  7. Reading a Failed Bearing
IVPower Transmission · pp. 25-32
  1. Pulley and Sprocket Speeds
  2. V-Belt Tension and Sheave Alignment
  3. Roller Chains
  4. Gear Types and Where They Go
  5. Gear Ratio, Speed and Torque
  6. Backlash and Tooth Contact
  7. Coupling Types
  8. Keys and Keyways
VShaft Alignment · pp. 33-40
  1. Offset and Angular: The Two Misalignments
  2. Soft Foot: Check It First
  3. Setting Up Rim-and-Face Indicators
  4. The Validity Check and Why the Rim Reads Double
  5. Bar Sag
  6. Working Out Shims with Similar Triangles
  7. The Reverse Dial Method
  8. Thermal Growth and Cold Alignment Targets
VIRigging and Hoisting · pp. 41-47
  1. Finding the Centre of Gravity
  2. Sling Angle and Leg Tension
  3. Hitches: Vertical, Choker, Basket
  4. Inspecting Slings: Wire Rope, Chain, Synthetic
  5. Wire Rope Clips and Thimbles
  6. Shackles and Eyebolts
  7. Crane Hand Signals
VIIHydraulics and Pneumatics · pp. 48-55
  1. Pascal's Law: Force = Pressure × Area
  2. Cylinder Speed from Flow
  3. Hydraulic Pumps: Gear, Vane, Piston
  4. Reading Symbols: Pumps, Motors, Lines
  5. Reading Symbols: Directional Control Valves
  6. Pressure and Flow Valves
  7. Accumulators and Stored Pressure
  8. Fluid, Contamination and Pneumatic FRL
VIIIPumps, Installation and Vibration · pp. 56-61
  1. Centrifugal Pumps and Cavitation
  2. The Affinity Laws
  3. Packing or Mechanical Seal
  4. Positive Displacement Pumps
  5. Setting a Machine: Base, Level, Grout
  6. Vibration: What the Frequency Tells You
IXFinal Review · pp. 62-65
  1. Every Formula on One Page
  2. Numbers to Remember
  3. The Most Common Mistakes Before the Exam
  4. Exam-Day Checklist

One Page, One Topic, All Clear

Think of it this way:

You're setting up indicators on a pump and motor, or the exam shows you two dial readings, and you have to decide: shim the motor or move it sideways first?

You open the alignment page and see it drawn: offset and angular, vertical and horizontal, the four values marked on the coupling, the ones every alignment corrects.

Offset and angular, vertical and horizontal: the four values every alignment corrects.

Same with pulley speeds, sling angles, Pascal's law, cavitation and bearing fits: each one on its own page, with the formula and a worked example in metric.

Millwright Exam Illustrated is 9 parts and 61 topics, all drawn, ending with every formula on one page, the numbers to remember and an exam-day checklist.

What you see drawn, you don't have to memorize.

What's Inside Millwright Exam Illustrated:

Ipp. 5-9

Before You Start: Exam and Safety

Know what the exam looks like before you sit it: how it's built, lockout to zero energy, oxy-fuel and hot work, bolt grades and tap drill sizes

IIpp. 10-17

Measuring and Trade Math

Metric micrometer, vernier caliper, dial indicator and TIR, conversions, areas and tank volumes, load weight, thermal expansion and fits

IIIpp. 18-24

Bearings

Pick the right bearing by the load it carries: plain or rolling, reading a bearing number, which ring gets the tight fit, mounting, adapter sleeves, grease quantity and failed bearings

IVpp. 25-32

Power Transmission

Pulley and sprocket speeds, V-belt tension, roller chains, gear types, ratio and torque, backlash, couplings, keys and keyways

Vpp. 33-40

Shaft Alignment

Go from two dial readings to the right move, shim or slide: offset and angular misalignment, soft foot, rim-and-face setup, the validity check, bar sag, shims with similar triangles, reverse dial and thermal growth

VIpp. 41-47

Rigging and Hoisting

Centre of gravity, sling angle and leg tension, hitches, sling inspection, wire rope clips, shackles, eyebolts and crane hand signals

VIIpp. 48-55

Hydraulics and Pneumatics

Force = pressure × area, cylinder speed, pump types, symbols for pumps, lines and valves, pressure and flow valves, accumulators, fluid and FRL

VIIIpp. 56-61

Pumps, Installation and Vibration

Centrifugal pumps and cavitation, the affinity laws, packing or mechanical seal, positive displacement pumps, setting a machine and vibration frequencies

IXpp. 62-65

Final Review

Every formula on one page, the numbers to remember, the most common mistakes and an exam-day checklist

At the end of the book: Every formula on one page, the numbers to remember and an exam-day checklist.

Plus: 2 Free Books

Exam-Style Practice Book: 4-Option Questions with Answers

BONUS 1: «Exam-Style Practice Book: 4-Option Questions with Answers»

Value on its own: US$ 17.90

Practise with multiple-choice questions on every topic in the book, each with the answer explained, so the exam format feels familiar before the day.

The 15 Most Common Millwright Mistakes, Before and After

BONUS 2: «The 15 Most Common Millwright Mistakes, Before and After»

Value on its own: US$ 14.90

See the most frequent errors in alignment, bearing fitting, rigging and trade math drawn side by side with the right way, so you spot them in the exam and on the floor.

Millwright Exam Illustrated with 2 Free Books

  • Millwright Exam Illustrated: 65 illustrated pagesUS$ 63
  • BONUS 1: Exam-Style Practice Book: 4-Option Questions with AnswersUS$ 17.90
  • BONUS 2: The 15 Most Common Millwright Mistakes, Before and AfterUS$ 14.90
  • High-resolution PDF to printIncluded
Total value US$ 95.80
YOUR PRICE:
US$ 27
You save US$ 68.80
YES, I WANT MILLWRIGHT EXAM ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

Secure purchaseEncrypted payment30-day guarantee

PDF by email: We email you Millwright Exam Illustrated as a PDF, together with the two free books. It's a single payment: no installments, no extra charges.

Who This Book Is For

You're in your final apprenticeship period

You're in your final apprenticeship period

Each module topic on one drawn page, in the same order every time, so you can review a topic at a glance between shifts.

Your exam date is set

Your exam date is set

The formulas, symbols and numbers you need, worked out in metric, plus practice questions in exam format to get used to the four options.

You've done the work for years without the ticket

You've done the work for years without the ticket

What you already do by hand, laid out the way the exam asks it in theory, so the challenge feels like your own trade on paper.

Everything You Get Today

US$ 95.80US$ 27
YES, I WANT MILLWRIGHT EXAM ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

30DAYS
GUARANTEE

30-Day Guarantee

Try Millwright Exam Illustrated for 30 days, bonus books included.

We refund everything if the file won't open, if the book isn't what you see here, if you were charged twice or if the email doesn't arrive. Just email us.

You pay once. No subscriptions.

Frequently Asked Questions

Is it for me if I've worked as a millwright for years without the ticket?

Yes. It's built for final-period apprentices and trade qualifiers. It doesn't start from zero: each page goes straight to the drawing, the numbers and the steps the exam asks about.

Where does the content come from?

It's checked against the Red Seal Occupational Standard for Industrial Mechanic (Millwright), with reference to CSA Z460 for lockout and to provincial OHS regulations. The Red Seal exam is interprovincial, so the trade content applies across Canada; for lockout and hoisting, your province's rules always come first. Worked examples are in metric, with a page of imperial conversions.

Is this official material?

No. It's an independent illustrated study book. It is not published, approved or endorsed by the Red Seal Program or any provincial apprenticeship authority, and it doesn't give you a certificate or count toward your hours: your Certificate of Qualification comes only from your provincial authority.

Does it replace my apprenticeship training?

No. It doesn't replace your technical training, your hours on the job or your employer's safety procedures. What it adds: your modules explain each topic in paragraphs and every video goes in its own order; here each topic is one drawn page, always laid out the same way, so you can review it at a glance.

Are the practice questions the ones on the exam?

No. They're written for this book, in a four-option format, to practise each topic. They are not official exam questions.

When and how do I get it?

The book and the 2 bonus books come as a PDF by email, to the address you enter at checkout.

Do I have to pay every month?

No. It's a single payment. No subscription.

Can I have it on paper?

Yes. The PDF is made to print, at home or at a print shop, so you can keep it in your toolbox.

How does the refund work?

You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.

Before You Close This Page

No more rereading the module with nothing sticking.

Rim-and-face readings: you see them drawn, and that's it.

You walk into the exam knowing where everything is.

Drawings make studying faster.

The book is right below.

One-time payment: US$ 27 · Guarantee: 30 days · PDF by email

YES, I WANT MILLWRIGHT EXAM ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.